Whether separate impact sound insulation is required depends on the flooring. Some products already have insulation built in, while others require a suitable underlay to be installed separately. The underlay must be compatible with the product, the subfloor, and, if applicable, the underfloor heating system. An additional underlay may only be used under flooring with built-in insulation if this is expressly approved.

Laminate flooring can be installed without an additional impact sound underlay if suitable sound insulation is already built into the product and the installation instructions specify this. If no sound insulation is built in, a suitable underlay is generally required. Therefore, always check the product construction and the accompanying instructions before installation.

The type of underlayment to use under laminate flooring depends on the product, the subfloor, and the room. For laminate flooring without built-in insulation, a suitable impact sound underlayment is often used. On mineral subfloors such as screed or concrete, a suitable moisture barrier is also required. If underfloor heating is installed, the entire floor structure must be approved for this purpose.

When installing laminate flooring on mineral subfloors such as screed, concrete, or tile, appropriate moisture protection is required. This can be a separate PE film or an underlayment that already has moisture protection built in. Follow the installation instructions for the laminate flooring and the specifications for the underlayment you are using.

The appropriate underlayment depends on the type of flooring, the installation method, and the subfloor. For click-lock flooring installed as a floating floor, a suitable underlayment may be required or may already be integrated. Flooring installed with full-surface adhesive has different requirements for subfloor preparation. Moisture and radiant floor heating must also be taken into account. The instructions for the specific product are decisive.

This may be possible depending on the product and the condition of the tiles. The subfloor must be solid, load-bearing, level, and prepared in accordance with the installation specifications. Grout lines and unevenness must not become visible later or compromise the bond. Selected CERAMIN floor and wall coverings are suitable for renovations over existing coverings, provided that the subfloor and product are approved for this purpose.

Select CERAMIN flooring products can be installed over hot-water and electric floor heating systems. However, the specific floor structure is always the deciding factor. The flooring, subfloor, installation method, and heating system must all be compatible with one another. Therefore, you should check the technical specifications and installation instructions for the desired product before installation. The low installation height of select CERAMIN products can be particularly advantageous during renovations.

Yes, thanks to the click system, many laminate floors can be installed even by experienced DIYers. This requires a clean, dry, load-bearing, and sufficiently level subfloor, as well as the appropriate underlayment. Follow the product-specific installation instructions carefully and observe the required edge clearances.

Click vinyl is a type of vinyl flooring whose planks are connected via a click system and are usually installed as a floating floor. If you’re looking for this type of installation but want to avoid PVC, CERAMIN flooring with a click system is available. The right product for you depends, among other things, on the room, the subfloor, and the desired installation method.

Click-and-glue systems have different applications. Click systems are often suitable for renovations and DIY projects because the tiles are installed as a floating floor. Floors installed with full-surface adhesive bonding are firmly attached to the prepared subfloor. CERAMIN offers both click systems and Dryback products for full-surface adhesive bonding. The key factors to consider are the room, the subfloor, the expected wear and tear, and product approval.

Common mistakes include an uneven or inadequately prepared subfloor, an unsuitable underlayment, untested residual moisture, incorrect wall clearances, and an inappropriate installation method. Joints and transitions must also be installed according to the manufacturer’s instructions. Always read the installation instructions for the specific product before you begin.

For a standard installation, you should generally allow for about 5 to 7 percent waste. For more complex installation patterns, such as herringbone, up to 15 percent may be required. The shape of the room, the size of the planks, and the direction of installation all affect the actual amount needed.

Yes, individual planks can generally be replaced. With click-lock flooring, this requires some technical skill because, depending on the plank’s position, part of the floor may need to be dismantled or the damaged plank replaced properly. Be sure to follow the instructions for the specific installation system, and if you’re unsure, consult a professional contractor.

The appropriate cleaning method depends on the material, surface, and intended use. Remove loose dirt regularly by sweeping or vacuuming, and use only suitable cleaning and care products. You can find specific instructions for each product or in the download section.